Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.9.0 Join the beta Download soon

Guide

A free SPICE simulator for Linux, with a schematic editor

BetterSPICE is a free SPICE circuit simulator for Linux with a schematic editor that runs the circuit while you draw. It comes as a .deb for Ubuntu and Debian, a pacman package for Arch, a Nix flake for NixOS and an AppImage for other x86-64 systems, with ngspice 47 for vendor models and no Wine. The packages open with the GitHub repository; join the beta for them now.

Checked on 20 November 2026. BetterSPICE beta 0.9.0. Facts about other tools are from the sources at the bottom, each with the date it was read.

Packages for Linux

Every package comes in two sizes: the program alone, and the program with the vendor model library, which can also be added later. All of them are listed as coming soon on the download section, together with the GitHub repository. Join the beta to get the installers now.

ForApp onlyWith the model libraryUpdate
Ubuntu and DebianUbuntu 24.04 and other Debian-based systems.deb, 75 MB.deb with the library, 839 MBSigned patch of the changed files, about 90 MB
Arch LinuxArch and derivatives, pacman -Ubetterspice, 69 MBbetterspice-models, 609 MBSigned patch, -Arch-Patch file
NixOS and NixVersion 0.9.0Flake, builds on your machine, 69 MBPrebuilt closure, 916 MBFrom the new flake; no in-app update
Any LinuxAppImage, x86-64AppImage, 151 MBAppImage with the library, 467 MBThe AppImage is replaced as a whole

Sizes are from the site’s download section for beta 0.9.0. The Debian, Arch and AppImage installers there are 0.5.0; Help > Check for updates brings a new install to 0.9.0 in one step.

What you get

  • A schematic editor that runs. The circuit simulates while you draw: wire colours follow the voltage and dots show the current. F5 runs the full analysis: transient, AC, DC sweep, operating point, parameter step, FFT, noise, pole-zero, loop gain, Monte Carlo and worst case.
  • No Wine. It is a native Linux program. The single exception is Texas Instruments models that Cadence has encrypted: they need PSpice for TI, which runs under Wine on Linux. Without it BetterSPICE uses fitted models and says so.
  • ngspice 47 for vendor models. The built-in engine runs the live view and the analyses, and ngspice 47 runs the 169,574 catalogue models. The Nix package builds against the ngspice in nixpkgs.
  • Imports. KiCad 6 to 10, EasyEDA Pro, LTspice .asc, Altium and Multisim schematics. See simulating a KiCad schematic.
  • Checked. The release compares 438 test circuits with ngspice: 3,797 of 3,797 signals pass, and 1,095 more are checked against a closed form or a datasheet window. A TI TLV9062 follower with 1 V in reads 1.00011272134857 V on Windows, Ubuntu and Arch.

NixOS, AppImage and first start

On NixOS, use the Nix package rather than the AppImage. It builds from source on the system’s own WebKitGTK, Mesa and graphics drivers, with ngspice from nixpkgs and the bspice command line. Add the model library zip to the Nix store once, then run or install it:

Terminal
$ nix run .#betterspice-full
$ nix profile install .#betterspice-full

The AppImage also runs on NixOS through run-betterspice-nixos.sh, which uses appimage-run. If the window stays blank or the start stops with an EGL_NOT_INITIALIZED error, check that hardware.graphics.enable = true is set, then try WEBKIT_DISABLE_DMABUF_RENDERER=1 (BetterSPICE’s default on Linux) or =0 in front of the command. The details are in manual chapter 1.

What is tested

The Linux packages are built and tested on Ubuntu 24.04 and current Arch, on a virtual display. Other distributions, a real GPU and Wayland are not tested.

Use it from the command line

bspice runs the same engine without a window, on the same circuit files, so it fits a script or a CI job. It reads and writes plain files, prints JSON or CSV on standard output, and exits 0 on success, 1 when a check found errors and 2 for a usage error.

Terminal
$ bspice validate examples
$ bspice op examples/basics/voltage-divider.bsc
$ bspice tran rc.bsc --stop 10m --max-step 10u --out run.csv
$ bspice export-spice rc.bsc -o rc.cir
$ bspice verify verification/circuits --failures

export-spice writes an ngspice netlist with every model parameter spelled out, so you can run the same circuit in plain ngspice. verify runs circuits in BetterSPICE and in ngspice and compares every signal. The list of commands is in chapter 71, and an AI agent can drive the same tools (agent page).

BetterSPICEngspiceQucs-SLTspice
What it isSchematic editor with its own live engine, and ngspice for vendor modelsSimulator: netlist in, results outSchematic GUI for outside simulators, ngspice among themFree simulator from Analog Devices
Linux.deb, Arch package, Nix flake, AppImageBuilds and packages for Linux [1]Packages for Linux [2]No Linux download is listed [3]
Schematic editorYesNo, third-party front ends [1]Yes [2]Yes
Runs while you drawYesNoNoNo, you run a simulation
LicenceAGPL v3.0 with the Commons ClauseOpen source [1]GPL-2.0 [2]Free download from ADI [3]

These are different jobs, and they combine: BetterSPICE uses ngspice 47 inside, and Qucs-S can drive ngspice too. A fuller comparison with sources is on BetterSPICE vs LTspice. On Linux, KiCad’s own simulator is also an ngspice front end; BetterSPICE opens its files.

Sources

  1. ngspice, ngspice.sourceforge.io, read on 18 November 2026: open source, no schematic entry, operating systems.
  2. Qucs-S, GitHub repository and project site, read on 18 November 2026: GPL-2.0, Linux packages.
  3. Analog Devices, LTspice, as archived on 17 September 2026: Windows and macOS downloads, no Linux download listed.
  4. BetterSPICE: the download section and its known limits, chapter 1, chapter 71, chapter 75, chapter 76, license.

See the live view first

Run the full app in your browser at app.bspicesim.com, or read install details in the manual.

Questions people ask

Is there a free SPICE simulator for Linux with a schematic editor?

Yes. BetterSPICE is free and has a schematic editor that simulates while you draw. Packages exist for Ubuntu and Debian, Arch, NixOS and an AppImage for other x86-64 distributions. It is a beta, and the downloads open together with the GitHub repository. Qucs-S is another option, and KiCad has a built-in ngspice front end.

Do I need Wine?

No. BetterSPICE is a native Linux program. Only Texas Instruments models that Cadence has encrypted need PSpice for TI, which runs under Wine. Without it, BetterSPICE uses fitted models and says so.

Is LTspice available for Linux?

Analog Devices’ LTspice page, as archived on 17 September 2026, lists downloads for Windows and macOS and none for Linux.

Which distributions are tested?

Ubuntu 24.04 and current Arch, on a virtual display. Other distributions, a real GPU and Wayland are not tested, so a different setup may need the graphics workarounds in the manual.

Does it need ngspice installed?

The ngspice 47 library comes with BetterSPICE; the Nix package uses the one from nixpkgs. The status bar shows “ngspice 47 ready” when it is found. Without it, circuits made of built-in parts still run.

Can I use it in a script or CI job?

Yes. The bspice command runs validate, op, tran, ac, dc, export-spice and verify without a window and prints JSON or CSV. Exit code 0 means success, 1 means errors were found and 2 means a usage error.