Calculators PCB
PCB trace width calculator (IPC-2221 and IPC-2152)
Enter the current and the temperature rise you allow, and the calculator gives the trace width, or the current a width carries. IPC-2221 uses I = k · ΔT0.44 · A0.725, with k = 0.048 for outer and 0.024 for inner layers and A the copper cross section in square mil. Copper weights from 0.5 to 4 oz are in the list.
IPC-2152 uses the Brooks and Adam closed-form fit of the IPC-2152 charts and counts the board thickness and a copper plane under the trace, which lets a trace carry more current for the same rise. Both methods give the trace resistance at its temperature, the voltage drop and the heat over the length.
The calculator
The formulas it uses
These are the formulas the calculator shows, copied from its source code. The results in the window above come from the same code as the app.
IPC-2221, outer layer
- I = k · ΔT^0.44 · A^0.725 (k = 0.048 outer, A in mil²)
- W = A / (t · 1.378 mil/oz)
- R = (ρ(T) · L) / (W · t)
- ρ(T) = 1.724e-8 Ω m · (1 + 0.00393 (T − 20))
IPC-2152 fit (Brooks and Adam)
- ΔT = K · I^a · W^b · Th^c
- a, b, c = 2, -1.15, -1, K = 215.3 (W and Th in mil, K by width for internal 0.5 and 3 oz, Appendix 6)
- board and plane: area × 24.93 t^−0.755 (board, mil) × (0.00313 d + 0.4045) (plane distance d, mil), ΔT × area^(−b)
- R = (ρ(T) · L) / (W · t)
- ρ(T) = 1.724e-8 Ω m · (1 + 0.00393 (T − 20))
IPC-2221, inner layer
- I = k · ΔT^0.44 · A^0.725 (k = 0.024 inner, A in mil²)
- W = A / (t · 1.378 mil/oz)
- R = (ρ(T) · L) / (W · t)
- ρ(T) = 1.724e-8 Ω m · (1 + 0.00393 (T − 20))
Sources. IPC-2221 (generic standard on printed board design, section 6.2 and chart 6-4, the I = k dT^0.44 A^0.725 fit). IPC-2152 (Standard for determining current-carrying capacity in printed board design, 2009): the baseline curves are charts, this uses the Brooks and Adam closed-form fit of them ("Trace Currents and Temperatures Revisited", 2015). The board thickness and plane distance factors are the IPC-2152 section 5 modifier charts as fitted by NinjaCalc. Copper: 1 oz = 1.378 mil, ρ = 1.724e-8 Ω m, 0.393 % per K.
Simple and Advanced
Simple is the main values, one set of results and a plot. Advanced is the full design view: the operating range with its corners, tolerance and temperature, checks with their margin (a green tick, an amber warning or a red cross), the parts to order with the ratings they need, warnings that give the fact, the number and the fix, and plots over the whole range. A value typed in one view is the same in the other.
In the app it also places the circuit and checks it
In the app, the buttons under the result act on your circuit: Add the trace to the circuit and run, Note on the trace's wire.
The last tab of the Advanced view, Verify in simulation, places the calculator's circuit and runs it, with measurements whose pass limits are the calculator's own numbers. A row the simulator cannot check says so and why. More in the manual: Trace current and width.
Goes with this one
All 17 calculators
Circuit
Parts
PCB
- Trace current and width
- Via current and parasitics
- Trace impedance
- Wire gauge and fusing