Calculators PCB
PCB trace impedance calculator (microstrip and stripline)
Pick the structure: microstrip, buried microstrip, stripline, or an edge-coupled differential pair on the surface or inside the board. From the trace width, the dielectric height, the copper thickness and εr, the calculator gives Z0, the effective permittivity and the delay, and the width for a target impedance.
Microstrip uses Hammerstad and Jensen (1980) with the thickness correction; stripline uses Cohn (1955) and Wheeler (1978). Differential pairs use Kirschning and Jansen for coupled microstrip and Cohn for coupled stripline, the same coupled-line model as the simulator's line parts, so the calculator and a placed line agree.
The calculator
The formulas it uses
These are the formulas the calculator shows, copied from its source code. The results in the window above come from the same code as the app.
Microstrip (Hammerstad-Jensen)
- Z0 = (60 ln(F / u + √(1 + (2 / u)²))) / (√εeff)
- εeff = (εr + 1) / 2 + (εr − 1) / 2 · (1 + 10 / u)^(−a b)
- u = w / h, the copper thickness widens u a little (Δu). F is a fit in u
- delay = √εeff / c
Buried microstrip (Hammerstad-Jensen, cover)
- Z0 = (60 ln(F / u + √(1 + (2 / u)²))) / (√εeff)
- εeff = (εr + 1) / 2 + (εr − 1) / 2 · (1 + 10 / u)^(−a b)
- u = w / h, the copper thickness widens u a little (Δu). F is a fit in u
- cover: εeff → εr as 1 − e^(−1.55 h2 / h) (IPC-2141 form)
- delay = √εeff / c
Stripline (Cohn, Wheeler)
- Z0 = (94.15 / √εr) / (w / (b (1 − t/b)) + Cf)
- w / (b − t) under 0.35: Z0 = 60 / √εr · ln(4 b / (π d)), d the round wire equivalent
- b = 2 h + t, delay = √εr / c
Differential microstrip (Hammerstad-Jensen, Kirschning-Jansen)
- Z0 = (60 ln(F / u + √(1 + (2 / u)²))) / (√εeff)
- εeff = (εr + 1) / 2 + (εr − 1) / 2 · (1 + 10 / u)^(−a b)
- u = w / h, the copper thickness widens u a little (Δu). F is a fit in u
- Zdiff = 2 Zodd (Kirschning-Jansen coupled microstrip)
- delay = √εeff / c
Differential stripline (Cohn)
- Z0 = (94.15 / √εr) / (w / (b (1 − t/b)) + Cf)
- w / (b − t) under 0.35: Z0 = 60 / √εr · ln(4 b / (π d)), d the round wire equivalent
- Zdiff = 2 Zodd (Cohn coupled stripline)
- b = 2 h + t, delay = √εr / c
Sources. Microstrip: E. Hammerstad and O. Jensen, "Accurate models for microstrip computer-aided design", IEEE MTT-S 1980, with the thickness correction, as in Brian Wadell, Transmission Line Design Handbook (1991), 3.2. Stripline: Cohn (1955) thick strip formula and Wheeler (1978) round wire form, Wadell chapter 4. Buried microstrip: the cover blend uses the exp(-1.55 h2 / h) form of IPC-2141 (Controlled Impedance Circuit Boards and High Speed Logic Design). Differential: Kirschning and Jansen (IEEE MTT-32, 1984) coupled microstrip and Cohn (1955) coupled stripline, as in the engine tline_diff part. The line test places the ideal tline part with the Z0 and delay found here.
Simple and Advanced
Simple is the main values, one set of results and a plot. Advanced is the full design view: the operating range with its corners, tolerance and temperature, checks with their margin (a green tick, an amber warning or a red cross), the parts to order with the ratings they need, warnings that give the fact, the number and the fix, and plots over the whole range. A value typed in one view is the same in the other.
In the app it also places the circuit and checks it
In the app, the buttons under the result act on your circuit: Place line test and run, Put the line in series with the selected wire. The circuit is drawn with library symbols, wires, a source and probes, placed at a free spot in the view, and the analysis that checks it runs at once. With parts selected, Apply to the selected parts writes the result into them, as one undo step.
The last tab of the Advanced view, Verify in simulation, places the calculator's circuit and runs it, with measurements whose pass limits are the calculator's own numbers. A row the simulator cannot check says so and why. More in the manual: Trace impedance.