Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.8.1 Join the beta Download soon
Part VII  Design calculatorsReferenceContentsIndex
51

LC resonance and Q

Resonance of an inductor and a capacitor: a tank in an oscillator or a filter, a series trap, a matching network. The Simple view gives f0, the characteristic impedance, Q and the bandwidth. The Advanced view uses real parts (the inductor’s Q, DCR and self-resonance, the capacitor’s loss and ESL, the board stray), the source and load, the tolerance and temperature, and the stress at resonance. Group Circuit. Search words include lc, resonance, tank, q, bandwidth, characteristic impedance and f0.

The window, the Simple and Advanced views, full screen and the place buttons are in The calculator window.

51.1Simple: f0, Z0 and Q

Simple: f0, Z0 and Q
ChoiceOptionsWhat it does
CircuitSeries, Parallel tankSeries: the output is taken across R, a band pass that peaks at f0. Parallel tank: fed through R, which sets its Q.
Simple: f0, Z0 and Q
FieldUnitDefaultWhat it does
InductancenH, µH, mH10 µHSOLVE. Reads a selected inductor.
CapacitancepF, nF, µF100 pFSOLVE. Reads a selected capacitor.
Resonant frequencyHz, kHz, MHz5.033 MHz (solved)SOLVE, solved when the calculator opens.
ResistanceΩ, kΩ10 ΩIn series with L and C, or feeding the tank. Reads a selected resistor.

f0 = 1 / 2π√(LC), Z0 = √(L/C), Q = Z0/R (series) or R/Z0 (tank), BW = f0/Q, and L or C from f0 and the other.

Simple: f0, Z0 and Q
ResultWhat it is
Resonance f0Orange.
Characteristic Z0
Q
Bandwidth (−3 dB)

"Q is 0.032, below 0.5: the circuit is overdamped and shows no peak." warns when Q is under 0.5. The Response plot is the circuit’s own transfer around f0 with f0 and the −3 dB edges marked.

Simple: f0, Z0 and Q
ButtonWhat it does
Place as circuitV1 (1 V at f0), L1, C1 and R1 as series or tank, IN and OUT probed.
Place and run AC analysisThe same and an AC sweep at 200 points per decade. Resonance gain at f0 within ±0.05 dB of 0 dB and Resonance phase at f0 within ±1°.
Apply to selected partsWith an inductor and a capacitor selected: l and c.
Try it
10 µH and 100 pF
  1. Open LC resonance and Q (type lc): series, 10 µH, 100 pF, 10 Ω.
  2. Press Place and run AC analysis.

You should seef0 5.03 MHz, Z0 316 Ω, Q 31.6, bandwidth 159 kHz. The AC run reads 0 dB and 0° at f0 and both pass.

51.2Advanced: real parts

LC resonance and Q, Advanced, in full screen: the series circuit with real parts, the response with the part tolerances, the parts, the checks, the impedan
Figure 51.1LC resonance and Q, Advanced, in full screen: the series circuit with real parts, the response with the part tolerances, the parts, the checks, the impedance with the self-resonance, the Q budget, the stress and f0 against temperature.
Advanced: real parts
ChoiceOptionsWhat it does
CircuitParallel tank, SeriesLoads that circuit’s source, load and band: series 50 Ω and 50 Ω for 1.5 MHz, parallel 10 kΩ and 10 kΩ for 300 kHz.
Solvef0 from L, C, C for f0, L for f0C or L is then SOLVED, worked out with the strays subtracted and rounded to E24 (C) or E12 (L).
Advanced: real parts
TabIts dotCards
DesignAmber with a warning.Result, Response with part tolerances, Parts.
Q and bandwidthThe insertion loss, bandwidth and spread checks.Q budget, f0 vs temperature, Checks.
Parts and stressThe SRF, voltage, current and dielectric checks.Impedance of the tank, Stress at resonance, Formulas.
Verify in simulationNone.Calculator vs simulation.
Advanced: real parts
FieldUnitDefaultWhat it does
L, C, f0, Board strayµH, pF, MHz, pF10, 100, 5, 2Group Resonator.
Tolerance, Q at f0, DCR, SRF, Tempco, I rating±%, , Ω, MHz, ppm, A5, 50, 0.3, 60, 100, 0.5Group Inductor (datasheet).
Tolerance, DF (tan δ), ESL, Rated, Dielectric±%, %, nH, V2, 0.1, 0.6, 50, C0GGroup Capacitor. Film and X7R too.
Source R, Load R, Drive, BW targetΩ (kΩ for a tank), V pk, kHz50, 50, 1, 1500Group Source, load and range.
T min, T max°C−20, 70

How it works it out. The inductor is (Rac + jωL) in parallel with its self-capacitance Cp = 1 / (L (2π SRF)²), with Rac = X / Q at f0, growing as √f and never below the DCR. The capacitor is DF/(ωC) + jωESL + 1/(jωC). The stray sits across the tank. The resonance of the real tank is the peak (tank) or minimum (series) of |Z|, found numerically, and so are the −3 dB edges. Unloaded Q = X0 / (RL + RC), Rp = Q X0, loaded Q from Rp, the source and the load, insertion loss −20 log(1 − QL/Qu) (Zverev).

Advanced: real parts
ResultWhat it is
ResonanceOf the real parts, and the ideal 1/2π√LC.
BandwidthWith its edges.
Loaded QAnd the unloaded Q.
Insertion loss−20 log(1 − QL/Qu).
Z0 = √(L/C), R or Rp at f0
f0 rangeOver tolerance and temperature. Amber above a quarter of the bandwidth.
Peak stressThe capacitor voltage and the current in L.

The Parts card asks for the inductor’s Q for under 1 dB loss, an SRF of at least 10 × f0, a current rating of 1.5 × the RMS, a C0G capacitor and twice the peak voltage, and a trimmer when the spread is wide. When C or L is solved, a table shows the standard values around it with their f0 and error. Q budget shows each loss’s share of 1/Q (inductor, capacitor, source, load).

Advanced: real parts
CheckValue and limitPassesMarginalFails
Inductor SRF vs f0SRF · f010 × or more3 × or moreLess
Capacitor SRF vs f01/2π√(ESL C) · f010 × or more3 × or moreLess
f0 spread vs half the bandwidth±spread · BW/2Under BW/4Under BW/2More
Insertion loss (Q_L / Q_u)dB1 dB or less3 dB or lessMore
Bandwidth vs target%Within ±20 %Within ±50 %More
Capacitor voltage at resonanceV pk · rated2 × margin1.2 × marginLess
Inductor current at resonanceI rms · rated1.5 × marginWithin itOver
Capacitor dielectricC0G, film, X7RC0G or filmX7R: not for tanks
Advanced: real parts
MessageWhen it shows
"Resonance at 4.97 MHz, −1.3 % from 1/(2π√LC). The 2 pF stray adds to C, and the inductor self-capacitance (704 fF, SRF 60 MHz) raises the apparent L near the SRF. Select C for f0 to subtract them."The real f0 is more than 1 % from the ideal.
"Tolerance and temperature move f0 by ±…, … % of half the bandwidth. Use ±1 % C0G and a ±2 % inductor, add a ±… trimmer or widen the band."Spread over a quarter of the band.
"Loaded Q … is … % of the unloaded Q …, so … dB is lost in the parts. An inductor with Q ≥ … at f0 brings the loss under 1 dB."Insertion loss over 1 dB.
"Inductor SRF 6 MHz is close to f0, where L and Q differ from the datasheet table. Use a part with SRF ≥ 10 × f0."SRF under 3 × f0.
"Capacitor voltage at resonance is … peak (Q times the drive). Use a … V part."Over the rating with margin.
"The inductor self-capacitance and the stray resonate with L below this frequency. Use a smaller L."Solving C finds none.
"The target is above the inductor self-resonance, so no L value fits. Use a part with a higher SRF."Solving L finds none.
Advanced: real parts
CheckAnalysis and measurementLimit
Gain at f0AC around f0 with the real parts (L1 dcr and srf, C1 esr and esl)±0.3 dB
Resonance, −3 dB bandwidthRead from the AC plot
f0 spreadTolerance analysis: 100 Monte Carlo runs of L and C, gain at the nominal f0 inside the −3 dB bandThe yield
Advanced: real parts
ButtonWhat it does
Place circuit and run ACV1 at the drive, RS, the tank or series L1 and C1 with their losses (and a separate stray for a tank), RL, and an AC sweep at 200 points per decade.
Run tolerance analysistol on L and C and a Monte Carlo of 100 AC runs.
Apply to selected L and CTheir values.
Advanced: real parts
SimpleAdvanced
Inductance, Capacitance, Resonant frequencyL, C, f0
CircuitCircuit
Try it
The real 10 µH and 100 pF
  1. Open LC resonance and Q, press Advanced: series, inductor Q 50, SRF 60 MHz, C0G, 2 pF stray, 50 Ω source and load.

You should seeThe resonance is at 4.97 MHz, 1.3 % under the ideal 5.03 MHz, and the warning says the stray and the inductor’s self-capacitance pull it. Bandwidth 1.67 MHz (4.19 to 5.87 MHz), loaded Q 2.9 against 47 unloaded, 0.56 dB insertion loss, f0 range ±195 kHz. All eight checks pass. Set Solve to C for f0 at 5 MHz: exact 99.32 pF, E24 100 pF (−0.68 %).

Sources. Textbook second-order resonance (Hayt and Kemmerly), and Zverev, Handbook of Filter Synthesis, for the insertion loss. The tests check f0, the series and tank bandwidths, the pull of the self-capacitance and stray (−1.3 %), the insertion loss, and the placed circuits’ gain and tolerance yield against bspice.