Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.8.1 Join the beta Download soon
Part VII  Design calculatorsReferenceContentsIndex
54

Attenuator pads

Resistive pads that lose a set number of decibels while matching the impedance on both sides: to tame a hot signal, isolate a mixer or a cable, or match 75 Ω to 50 Ω. The Simple view gives symmetric Pi and T pads. The Advanced view adds the bridged T and the minimum-loss L pad, unequal ports, the power in each resistor, the tolerance and the package parasitics. Group Circuit. Search words include attenuator, pad, pi pad, t pad, db, matched and 50 ohm.

The window, the Simple and Advanced views, full screen and the place buttons are in The calculator window.

54.1Simple: Pi and T pads

Simple: Pi and T pads
ChoiceOptionsWhat it does
PadPi pad, T pad
Part valuesExact, Nearest E12, Nearest E24, Nearest E96Rounded to the nearest of the series.
Simple: Pi and T pads
FieldUnitDefaultWhat it does
AttenuationdB10
ImpedanceΩ, kΩ50Source and load.

With K = 10dB/20: Pi R1 = R3 = Z (K + 1) / (K − 1) to ground and R2 = Z (K² − 1) / 2K in series. T R1 = R3 = Z (K − 1) / (K + 1) in series and R2 = 2ZK / (K² − 1) to ground.

Simple: Pi and T pads
ResultWhat it is
R1, R3 and R2Rounded to the series (orange).
AttenuationWhat the rounded pad gives between Z and Z.
ErrorAttenuation given minus asked.
Input impedanceOf the rounded pad with Z at the other end.

A table By series compares Exact, E12, E24 and E96 (values, attenuation, error, input Z). "Enter an attenuation above 0 dB." shows at 0 dB or less.

Simple: Pi and T pads
ButtonWhat it does
Place and run AC analysisV1 (1 V, 1 kHz), RS = Z, the pad, RL = Z, IN and OUT probed, an AC sweep 10 Hz to 1 MHz. Measurement Pad gain at 1 kHz within ±0.02 dB of −(attenuation + 6.02 dB): the matched source halves the voltage.
Place as circuitThe same with no analysis.
Apply to selected resistorsWith three resistors selected: R1, R2, R3.
Try it
A 10 dB, 50 Ω Pi pad
  1. Open the attenuator pads: Pi, 10 dB, 50 Ω, E24.
  2. Press Place and run AC analysis.

You should seeR1 = R3 = 100 Ω and R2 = 68 Ω (exact 96.2 Ω and 71.2 Ω). They give 9.63 dB, an error of −0.37 dB, and 50.33 Ω in. OUT reads 15.65 dB below the source and the measurement passes.

54.2Advanced: four pads and their limits

The attenuator pads’ Advanced view in full screen: a 10 dB Pi pad in E24 values with its match, the power per resistor, the spread, the response with paras
Figure 54.1The attenuator pads’ Advanced view in full screen: a 10 dB Pi pad in E24 values with its match, the power per resistor, the spread, the response with parasitics and the checks.
Advanced: four pads and their limits
ChoiceOptionsWhat it does
PadPi, T, Bridged T, Minimum-loss LThe L pad matches two impedances with the least loss: with equal ports it sets 75 Ω and 50 Ω.
Advanced: four pads and their limits
TabIts dotCards
DesignThe worst check.Result, Circuit, Parts, Values by series.
PowerGreen when every resistor’s need fits its package, else amber.Power per resistor, Checks.
Match and toleranceGreen when the worst return loss of the Monte Carlo is 20 dB or more.Input match vs load match, Attenuation spread, Values by series, Error across settings.
FrequencyAmber when the response drifts below the top frequency.Response with parasitics.
Verify in simulationNone.Calculator vs simulation.

When the pad cannot be built only Design shows, with a red dot and the reason.

Advanced: four pads and their limits
FieldUnitDefaultWhat it does
Attenuation (Loss for the L pad, SOLVED)dB10Group Pad. Its badge says OK or Cannot be built.
Port 1 Z, Port 2 ZΩ50, 50The bridged T uses port 1 for both.
ValuesExact, E12, E24, E96
Tolerance±%1
Input powerdBm17Group Power: the source’s available power into a matched pad.
Margin×2On each resistor’s worst power.
Package0402, 0603, 0805, 1206, 2010, 2512Rating at 70 °C, ESL and Cp: 0402 63 mW, 0.4 nH, 0.03 pF … 2512 1 W, 1.5 nH, 0.2 pF.
Up toGHz6Group Frequency: the top frequency.
ESL each, Cp eachnH, pF0.5, 0.05Typical package values. Enter datasheet values where known.
Monte Carlo distributionNormal, Uniform

How it works it out. Exact values from the pad’s Z-parameters (Z11 = Z1 (1 + A²) / (1 − A²), Z22 likewise, Z21 = 2A √(Z1 Z2) / (1 − A²), A = 1/K): T R1 = Z11 − Z21, R2 = Z21, R3 = Z22 − Z21, and Pi from their dual. Bridged T: R1 = R2 = Z, R3 = Z / (K − 1), R4 = Z (K − 1). Minimum-loss L: Rseries = √(Zh (Zh − Zl)) on the high side, Rshunt = Zl √(Zh / (Zh − Zl)), loss 20 log(√ρ + √(ρ − 1)) with ρ = Zh/Zl. The rounded pad is then solved by nodal analysis for the attenuation, the return loss at both ports, the power in each resistor for a matched, open, shorted and reversed load, the response with ESL and Cp, and a Monte Carlo of 2000 draws.

Advanced: four pads and their limits
ResultWhat it is
AttenuationOf the standard-value pad, and the difference from what was asked.
Return lossPort 1 and port 2 (capped at 99 dB).
ZinAnd Zout.
SpreadThe worst attenuation change of the Monte Carlo, and the worst return loss.
Power in, Out, matcheddBm and W.
Hottest RThe worst-case power of the hottest resistor. Amber when one needs more than its package.
Flat toThe frequency where the attenuation moves 0.5 dB or the return loss drops below 20 dB, or > 6 GHz.

Under the tiles: the exact pad values, the voltage ratio, the isolation (a 10 dB return-loss load shows 10 dB plus twice the pad’s loss at port 1) and the noise figure (equal to the loss at 290 K). Power per resistor is a table of the four load cases with the hottest marked and the package each needs.

Advanced: four pads and their limits
CheckValue and limitPassesMarginalFails
Realisableyes or no · the minimum lossYesNegative resistors
Attenuation, standard partsdB · askedWithin 0.1 dBWithin 0.5 dBMore
Return loss, port 1 and port 2dB, with VSWR30 dB or more20 dB or moreLess
Return loss, toleranceworst of 2000 runs26 dB or more20 dB or moreLess
Attenuation spread± dBUnder 0.1 dBUnder 0.3 dBMore
R1 shunt (in) power, and each resistorworst W · rating × marginWithin the rating with the marginWithin the ratingOver: the package needed
Flat tofrequency · ESL, CpFlat to the topBreaks above a third of itLower
Advanced: four pads and their limits
MessageWhen it shows
"Minimum loss between 50 Ω and 200 Ω is 11.44 dB. 3 dB needs negative resistors. Set 11.44 dB or more, or use the minimum-loss L pad."Unequal ports and too little loss.
"A minimum-loss L pad needs unequal port impedances. Use Pi, T or bridged T."L pad with equal ports.
"R1, R2, R3 exceed the 0402 rating: 619 mW (> 2512 with ×2 margin), … Worst case: load open."A resistor over its package.
"Above 4.36 GHz the 0603 ESL and Cp shift the attenuation and the match. Use a smaller package or thin-film RF resistors."Not flat to the top frequency.
"Bridged T is symmetric. Both ports use the port 1 impedance."Bridged T with unequal ports.
Advanced: four pads and their limits
CheckAnalysis and measurementLimit
Gain of V(OUT) at 1 kHzAC with a Z1 source and a Z2 load±0.02 dB
Input matchAC, gain of V(IN) = 20 log |Zin / (Z1 + Zin)|±0.05 dB
Gain of V(OUT) at the top frequencyAC to the top frequency with esl and cp on each pad resistor±0.05 dB
Gain of V(OUT), worst caseWorst-case AC with tol on each pad resistorEvery corner inside
Power per resistorCalculator only (V²/R of the node voltages the AC run checks)
Advanced: four pads and their limits
ButtonWhat it does
Place and run ACV_PAD behind RS = Z1, the pad, RL = Z2, IN and OUT probed, 10 Hz to 1 MHz. Measurements Pad gain at 1 kHz and Pad input match.
Place and run with parasiticsesl and cp on each pad resistor, AC from 1 MHz to the top frequency.
Place and run worst casetol on the pad resistors, a worst-case AC of 200 runs. Pad gain at 1 kHz, worst case between the 2ⁿ tolerance corners.
Place circuitThe circuit only.
Advanced: four pads and their limits
SimpleAdvanced
AttenuationAttenuation
ImpedancePort 1 Z and Port 2 Z
Pad (Pi, T)Pad
Part valuesValues
Try it
Where the power goes
  1. Open the attenuator pads, press Advanced, and look at the Power tab: Pi, 10 dB, E24, 17 dBm, 0603.
  2. Set Input power to 30 and Package to 0402.

You should seeAt 17 dBm the hottest resistor is R1 with 31 mW when the load is open (25.2 mW matched). At 30 dBm every resistor fails: R1 needs 619 mW, and the warning names a 2512 as the package each needs with the ×2 margin.

Sources. Reference Data for Radio Engineers (ITT) for the Pi, T and bridged T, and the minimum-loss L pad formula. The tests check the published 50 Ω tables, the L pad 75 to 50 Ω (43.30 Ω and 86.60 Ω, 5.72 dB), the power per resistor by hand, and the placed pads against bspice’s AC within 0.02 dB.