Source code coming soon. The GitHub repository is private for now and opens to everyone very soon.
BetterSPICE Beta 0.8.1 Join the beta Download soon
Part VII  Design calculatorsReferenceContentsIndex
62

Via current and parasitics

A plated via: its resistance, inductance and capacitance, the current it carries, its thermal resistance, and how many a current needs. The Advanced view adds through, blind and microvias with their fill, the IPC fabrication rules (land, plating, aspect ratio), a thermal-via array under a power pad, the stub resonance against a data rate with back-drilling, and inserts the via into a wire of your circuit. Group PCB. Search words include via, plated, hole, barrel, parasitic, inductance, capacitance and thermal.

The window, the Simple and Advanced views, full screen and the place buttons are in The calculator window.

62.1Simple: one via or n

Simple: one via or n
ChoiceOptionsWhat it does
IPC-6012 classClass 2, Class 3The plating the class asks for: 20 µm or 25 µm average.
Simple: one via or n
FieldUnitDefaultWhat it does
Hole diameter (finished)mm, mil0.3 mm
Plating thicknessµm, mil25 µm
Via length (board thickness)mm, mil1.6 mm
Pad diameter, Antipad diametermm, mil0.6, 1.0 mm
Board εr4.5
CurrentA, mA2 AReads the measured RMS current of a selected wire or part.
Temperature rise, Ambient°C10, 25
Vias in parallel1 (solved)SOLVE, solved when the calculator opens: the number the current needs.

Barrel area A = πt(d + t), R = ρ(T) h / A, L = 5.08 h [ln(4h/d) + 1] nH and C = 1.41 εr T D1 / (D2 − D1) pF (Johnson and Graham, lengths in inches), Rθ = h / (kA) with k = 385 W/mK, and the current per via from IPC-2221 on the barrel section. n vias divide R, L and Rθ and add their C. Z = √(L/C).

Simple: one via or n
ResultWhat it is
ResistanceOf n in parallel (orange).
Inductance, CapacitanceOf n vias.
Current per via, Vias needed
Voltage drop, Thermal resistance
Via Z√(L/C) of one via.
Simple: one via or n
MessageWhen it shows
"The antipad must be larger than the pad, or the capacitance has no meaning."Antipad at or under the pad: the capacitance then reads negative and Via Z reads –.
"The pad is smaller than the plated hole."
"Aspect ratio over 10 to 1. Plating in a hole this deep is hard to make, so ask the fabricator or use a larger hole."
"The inductance formula assumes a via longer than it is wide."
"… A per via is more than one via carries for +10 °C. Use … or more."Too few vias typed.
"Plating 10 µm is under the IPC-6012 class 3 average of 25 µm. Specify at least 25 µm in the hole."

Drawings: the via from above (antipad, pad, plating, hole) and the barrel in cross section. Add the via R and L in series and run (with a straight wire of 8 grid units selected) puts R_VIA and L_VIA into it, in the live view, with no measurements.

Try it
2 A through 0.3 mm vias
  1. Open Via current and parasitics (type via): 0.3 mm hole, 25 µm, 1.6 mm, 2 A, +10 °C.

You should seeOne via carries 1.9 A, so 2 are needed: 572 µΩ, 1.14 mV, 650 pH (1.3 nH for one), 1.2 pF, 81.4 K/W, Via Z 46.6 Ω.

62.2Advanced: through, blind and micro

Via current and parasitics, Advanced, in full screen: two through vias for 4 A, with the fab spec, the thermal pad, the cross section, the land size, the s
Figure 62.1Via current and parasitics, Advanced, in full screen: two through vias for 4 A, with the fab spec, the thermal pad, the cross section, the land size, the stub response and the checks.
Advanced: through, blind and micro
ChoiceOptionsWhat it does
ViaThrough, Blind, MicroviaLoads typical geometry: through 0.3 mm, 25 µm, 1.6 mm, pad 0.6, antipad 1.0, drill allowance 0.1 mm. Blind 0.2 mm, 20 µm, 0.4 mm. Microvia 0.1 mm, 15 µm, 0.08 mm.
FillOpen (or tented), Epoxy (plugged), Paste (conductive), Copper (filled)Thermal k 0, 0.5, 3.5, 385 W/mK.
Advanced: through, blind and micro
TabIts dotCards
CurrentCurrent, and vias against the trace.Result, Temperature rise vs current, Fab spec.
Thermal padPad rise, fill, hole spacing.Thermal pad, θ vs pitch, Checks.
FabricationAspect ratio, plating, land, antipad.Cross section, Fabrication checks, Land size (IPC-2221).
StubStub resonance.|S21| with stub, Signal.
Verify in simulationNone.Calculator vs simulation.
Advanced: through, blind and micro
FieldUnitDefaultWhat it does
Hole (finished), Plating, Length, Pad, Antipad, εrmm, µm, mm, mm, mm0.3, 25, 1.6, 0.6, 1.0, 4.3Group Via.
Current, Rise allowed, AmbientA, °C, °C4, 20, 50Group Current, badge the vias needed.
Trace width, Trace coppermm, µm2.5, 47.9The trace the vias feed: they should carry what it carries.
Pad length, Pad width, Pitch, Power, Laminate kmm, mm, mm, W, W/mK3, 3, 1, 1.5, 0.3Group Thermal pad.
Drill over hole, Hole tol. ±, Ring minmm0.1, 0.05, 0.05Group Fabrication.
IPC-6012 class, IPC-2221 fabrication allowanceClass 2 or 3, A 0.4, B 0.25, C 0.2 mm
Data rate, Layer depth, tan δGb/s, mm25, 0.2, 0.02Group Signal.
Back-drill, Stub left, Line Z0, mm, ΩNo, 0.2, 50

How it works it out. The current per via uses the IPC-2152 fit on the barrel unrolled as an outer trace of width π(d + t), on the safe side (vias run cooler), and the vias needed is the current over that, rounded up. The trace match is the number of vias that carry what the entered trace carries at the same rise. The barrel impedance is 60/√εr ln(antipad / (d + 2t)), a coax in the antipad. The stub is the barrel below the signal layer (or what back-drilling leaves), with its notch at c / (4 l √εr) against the Nyquist frequency, half the data rate. The thermal array fits as many vias as the pitch allows in the pad, each a barrel and its fill, in parallel with the laminate between them. The minimum land is a + 2b + c: hole and tolerance, twice the ring, and the fab allowance.

Advanced: through, blind and micro
ResultWhat it is
Vias neededWith the current each (orange).
Resistance, DropOf n vias at their temperature.
IPC-2221 currentPer via, the older chart.
Inductance, Pad C, Barrel Z
Stub notchAmber under 3 × the Nyquist frequency.
Vias in pad, Board θ, RiseOn the Thermal pad card.
Advanced: through, blind and micro
CheckValue and limitPassesMarginalFails
Current, 2 viasI · per via × nWithin itUp to 1.11 × itMore
Vias vs tracen · the trace’s matchn ≥ matchFewer: use the match
Aspect ratio (drill)x : 18 or less (microvia 0.75)10 or less: advanced (microvia 1)More: too deep
Plating thicknessplating · class averageAt or over90 % or moreThin
Pad (IPC-2221 land)pad · minimum landAt or over95 % or moreBreakout
Antipad clearance(antipad − pad)/2 · 0.15 mmAt or over80 % or moreTight
Stub resonancenotch · Nyquist3 × or more2 × or moreLess
Thermal pad riserise · n vias, power20 °C or lessUp to 28.6 °CMore
Via fill in padfillFilled or tentedOpen: solder wicking
Hole spacingwall to wall · 0.2 mmAt or over90 % or moreToo close
Advanced: through, blind and micro
MessageWhen it shows
"… needs … vias of this size for +20 °C."Too few.
"The 2.5 mm trace carries 5.86 A at the same rise. Use 3 vias to match it."Fewer than the trace match.
"1.4 mm stub resonates at 25.8 GHz, 2.1× the 12.5 GHz Nyquist frequency of 25 Gb/s. Back-drill to 0.2 mm (181 GHz), route on a layer near the bottom, or use a blind via."Notch under 3 × Nyquist.
"Aspect ratio 8.0 : 1 exceeds 8 : 1. Plating thins in the middle of the hole. Use a hole of 0.3 mm or larger."
"Pad 0.6 mm is under the IPC-2221 minimum of 0.65 mm (hole + tolerance + 2 × ring + level C allowance). Drill wander can break out. Use a 0.65 mm pad."
"IPC-6012 class 2 requires 20 µm average plating in the hole."
"Open vias in a thermal pad wick solder from the joint. Tent, plug, or fill and cap them (IPC-4761 type VII), or place them at the pad edge."Fill Open.
Advanced: through, blind and micro
CheckAnalysis and measurementLimit
Drop at 4 AOperating point of R_VIA and L_VIA in the selected wireEqual
Spike for 1 A/nsL/n × 1 A/ns, a transient with a fast current step
Stub notchAC of a 50 Ω line with an open ideal line as the stub (barrel Z, delay from the stub length)At the quarter wave
Thermal pad riseNot simulated: set rth_ja on the part to the K/W for self-heating
Advanced: through, blind and micro
ButtonWhat it does
Insert in wire and runR_VIA (n in parallel, at temperature) and L_VIA (L/n) in the selected wire. See below.
Place stub test and run ACA 50 Ω source and load with the stub as an open ideal line, swept past the notch. Via stub loss at half the notch within ±0.1 dB, and Via stub notch under −15 dB. Greyed when there is no stub.
Apply θ to partThe thermal pad’s K/W as rth_ja on the selected parts.

Insert in wire and run puts the via into your circuit: select a straight wire first (horizontal or vertical, at least 4 grid units long, 8 for the via’s two parts). The part goes in series at the middle of the wire, 4 grid units long, and the wire is split at its pins. It is a resistor R_VIA with copper’s tempco (tc1 0.00393, tnom 20 °C) at the worst-corner temperature, so it has the calculator’s hot resistance. Then the live view runs, an operating point is taken, and two measurements are added: current against the calculator (PASS up to the design current) and drop, % of the calculator’s (PASS up to 100.1 %). A wire that carries more than the design current fails both. It is one undo step, and a name in use becomes R_VIA2. The button’s tooltip asks for a wire at least 8 grid units long in all three, while the trace and wire need only 4.

Advanced: through, blind and micro
SimpleAdvanced
Hole, Plating, Via length, Pad, Antipad, Board εrHole, Plating, Length, Pad, Antipad, εr
Current, Temperature rise, Ambient, IPC-6012 classCurrent, Rise allowed, Ambient, IPC-6012 class
Try it
4 A, a thermal pad and a 25 Gb/s stub
  1. Open Via current and parasitics, press Advanced: through, open, 4 A, +20 °C, a 3 × 3 mm pad with 1 mm pitch and 1.5 W, 25 Gb/s on a layer 0.2 mm deep.

You should see2 vias (2.53 A each): 0.631 mΩ, 2.52 mV, 1.30 nH each, 573 fF, barrel Z 30.4 Ω. Four rows are amber and one red: the 2.5 mm trace would need 3 vias, the 1.4 mm stub notches at 25.8 GHz (2.1 × the 12.5 GHz Nyquist, back-drill to 0.2 mm), the 9-via pad rises 26.4 °C, the open vias wick solder, and the 0.6 mm pad is under the 0.65 mm minimum land.

Sources. Johnson and Graham, High-Speed Digital Design (vias), IPC-2221 (current and land), IPC-2152 (the barrel as a trace), IPC-6012 (plating), IPC-4761 (via fill), IPC-2226 (microvia capture pad), the quarter-wave stub. The tests check the barrel R and θ, Johnson’s 1.18 nH for a 0.062 × 0.016 inch via, IPC-2221 and the unrolled IPC-2152 within 3 %, the land, plating, aspect ratio and pad array, the notch, and the placed R_VIA and stub test against bspice.